Graco 313537D Manual de usuario descargar pdf

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441

ti13583a

HTX 2030 Applicator

Model: 24B327

Maximum Fluid Working Pressure: 1,000 psi (6.9 MPa, 69 bar)

Maximum Air Working Pressure: 250 psi (1.7 MPa, 17 bar)

- For Water-Based Materials Only -

The following Warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point

symbol alerts you to a general warning and hazard symbols refer to procedure-specific risks. Refer back to these Warnings.

Additional, product-specific warnings may be found throughout the body of this manual where applicable.

PRESSURIZED EQUIPMENT HAZARD

Fluid from the applicator/dispense valve, leaks, or

ruptured components can splash in the eyes or on

skin and cause serious injury.

• Follow Pressure Relief Procedure in this manual, when

you stop spraying and before cleaning, checking, or ser-

vicing equipment

• Tighten all fluid connections before operating the equip-

ment.

• Check hoses, tubes, and couplings daily. Replace worn

or damaged parts immediately.

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes,

in work area can ignite or explode. To help prevent

fire and explosion:

• Keep work area free of debris, including solvent, rags

and gasoline.

• Ground all equipment in the work area. See Grounding

instructions.

• If there is static sparking or you feel a shock, stop oper-

ation immediately. Do not use equipment until you iden-

tify and correct the problem.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influ-

ence of drugs or alcohol.

• Do not exceed the maximum working pressure or tem-

perature rating of the lowest rated system component.

See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equip-

ment wetted parts. See Technical Data in all equipment

manuals. Read fluid and solvent manufacturer’s warn-

ings. For complete information about your material,

request MSDS forms from distributor or retailer.

• Check equipment daily. Repair or replace worn or dam-

aged parts immediately with genuine manufacturer’s

replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your

distributor for information.

• Route hoses and cables away from traffic areas, sharp

edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull

equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment

when operating, servicing, or in the operating area of

the equipment to help protect you from serious

injury. This equipment includes but is not limited to:

• Protective eyewear and hearing protection

• Clothing and respirator as recommended by the fluid and

solvent manufacturer

•Gloves

Pressure Relief Procedure

Follow this Pressure Relief Procedure

whenever instructed to relieve pressure,

stop spraying, check or service equipment,

or install or clean spray tip.

1. Shut off gasoline engine or unplug electric power cord

and turn sprayer pressure control to lowest pressure

setting.

2. Open drain valve at sprayer and verify pressure has

been relieved into supply pail.

If you suspect spray tip or hose is clogged or that pressure

has not been fully relieved after following the steps above,

place thick rag over connection between hose and sprayer or

applicator. Slowly loosen connection to relieve pressure

gradually. Clear hose or tip obstruction.

WARNINGS

WARNING

313537D

IMPORTANT SAFETY INSTRUCTIONS. Refer to your

sprayer instruction manual for Pressure Relief, priming and

spray instructions. Keep these instructions.

Instructions/Parts

English

1 2 3 4

Indice de contenidos

Pagina 1 - English

Pagina 2 - Air Spray Setup

2 313537DAirless Spray SetupTo prevent injury when the applicator is not in use, always relieve pressure if sprayer is being shut down or left unatte

Pagina 3 - Technical Data

313537D 3OperationSpraying1. Set material flow (see sprayer instruction manual for additional information).2. Spray test pattern3. Turn air knob on an

Pagina 4

For complete warranty information contact your local Graco distributor, call Graco customer service: 1-800-690-2894 or visit our website: www.graco.co

Comentarios a estos manuales

Sin comentarios

Graco 313537D Manual de usuario

Busca en linea o descarga Manual de usuario para No Graco 313537D. Graco 313537D User's Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para No Graco 313537D