Graco 3A1704G Manual de usuario

Instructions - PartsCommunications Gateway Module Installation KitFor use with HFR™, VRM™, and VPM™ systems to provide fieldbus communications abiliti

Available Internal Data 10 3A1704GSystem Status5 | DV Lockout / Circu-lation Control(1 = Locked out)1-2 0 = Unlock Dis-pense Valve, Non-Circula-tion S

Available Internal Data3A1704G 1110 | Base Purge (1 = On)0 = Park Pump ON1 =Base Purge ON0 = Park Pump ON1 =Base Purge ONPark mode is valid for all ma

Available Internal Data 12 3A1704GOperating ModeSystem Mode Select 3 DISABLED Mode = 13 DISABLED Mode = 1PLC selects the various modes of the dispensi

Available Internal Data3A1704G 13Bit 4 = 1, Red Hose heat enableBit 4 = 1, Red Hose heat ONBit 5 = 1, Blue Hose heat enableBit 5 = 1, Blue Hose heat O

Available Internal Data 14 3A1704GUnits and Operating InfoUnits and Operating InfoBit | Function-- -- 13-14 Bitxx | Meaning0-1 | Volume Units -- 0 0 |

Available Internal Data3A1704G 15Ratio of the Blue / Red mate-rial - set-pointDepending on system setup the units can be by weight or volume-- -- 23-2

Available Internal Data 16 3A1704GRed Hose Temp - ActualDepending on system setup the units can be read in C or F-- -- 53-54 Actual tem-peratureBlue T

Available Internal Data3A1704G 17Tank Material Level Sta-tus Feed-backTank Level High = 3 Tank Level Mid = 2Tank Level Low = 1-- -- 79 Bits 3-0 = Red

Available Internal Data 18 3A1704GADM Feedback-- -- 84Bits 3-0 = ADM Status bits.Bits 4-7 are broken down as follows:Bit 4 = System Power statusBit 5

Available Internal Data3A1704G 19Change Dispense Flow Rate or Pres-sure Set point Depending on system setup the units can be by weight, volume, flow,

Kits 2 3A1704GContentsKits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Related Manuals . . . . . . . . . . . . . .

Available Internal Data 20 3A1704GChange Tempera-ture Con-ditioning Set pointDepending on system setup the units can be read in C or FLSW = Desired se

Available Internal Data3A1704G 21Controlling DeviceCGM Control and Night ModeWhen the controlling device sets the HFR into night mode using the CGM, t

Available Internal Data 22 3A1704GTiming DiagramsThe following diagrams show the signal sequence of the CGM communication.Heart Beat Timing DiagramSys

Available Internal Data3A1704G 23System Startup and Dispensing Recirculation DiagramSystem Startup and Dispensing Recirculation SystemVerify Heat Zone

Parts 24 3A1704GPartsModel 24J415† Not included in kit. See Kits on page 2 for available CGM modules. See the Communications Gateway Module manual 312

Parts3A1704G 25

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th

Installation3A1704G 3Installation1. Install the CGM in the desired location.a. Remove access cover (D). Loosen two screws (C) and remove CGM (A) from

Installation 4 3A1704G4. If used, connect the ethernet, DeviceNet, or PROFI-BUS cable to the CGM as applicable. Connect the other end of the cable to

Setup3A1704G 5SetupGateway ScreensThe Gateway screens are used to configure the fieldbus. These screens are shown only if a CGM is correctly installed

Setup 6 3A1704GPROFINET Fieldbus ScreensThese screens are shown only if you have a PROFINET Fieldbus CGM installed. See Kits on page 2.Screen 1This sc

Setup3A1704G 7EtherNet/IP Fieldbus ScreensThese screens are shown only if you have a EtherNet/IP Fieldbus CGM installed. See Kits on page 2.Screen 1Th

Maintenance 8 3A1704GMaintenanceInstall Upgrade TokensNOTE: The Motor Control Module, Fluid Control Mod-ule, and Temperature Control Module connection

Available Internal Data3A1704G 9Available Internal Data The following internal data with this system can be viewed and modified by your fieldbus maste